Honda Prologue Wheels and Rims

Honda Prologue Aftermarket Wheel Fitment

The Honda Prologue is Honda's first mass market electric crossover, launched as a 2024 model year vehicle and built on the GM Ultium BEV3 platform out of GM's Ramos Arizpe plant in Mexico. One generation, one chassis, and one wheel fitment box across every Prologue year and every trim. 6x132 bolt pattern, 74.5mm hub bore, M14x1.5 lug nuts, and 6 lugs. Square fitment (same width front and rear). Drivetrain (front wheel drive or all wheel drive) does not change the bolt math. Trim (EX, Touring, Elite) does not change the bolt math. The Prologue is a 6 lug vehicle, not a 5 lug vehicle, which sets it apart from most of Honda's gasoline lineup and places it in a different aftermarket wheel family than the Accord, CR-V, and Pilot.

Find Your Honda Prologue Generation

Only one Prologue generation has been sold. It launched as a 2024 model and continues in production. Pick the year range below to see wheels and rims that fit your specific Prologue.

The Honda Prologue Bolt Pattern

Every Honda Prologue uses 6x132 with a 74.5mm hub bore and M14x1.5 lug nuts. The 6x132 pattern is the GM Ultium BEV3 platform spec used across the family of GM built electric crossovers and SUVs sharing this architecture. The Prologue's direct platform sibling is the Cadillac Lyriq, which runs the same 6x132 / 74.5mm / 6 lug bolt pattern in both rear wheel drive and all wheel drive configurations. The Chevrolet Blazer EV is the third vehicle on the same architecture out of the same Ramos Arizpe plant. Bolt math crosses cleanly across these three vehicles, although body styling, brake assembly options, and fender geometry are different on each.

Important safety note: the Prologue is a 6 lug vehicle. Honda's gasoline crossovers and sedans (Accord, CR-V, Pilot, Passport, HR-V) all use 5 lug patterns. A wheel built for any other Honda model will not bolt safely to a Prologue. The Prologue also does not share a bolt pattern with the older 5x120 BMW family or the 5x114.3 family used on most Asian luxury SUVs. The 6x132 hub family is its own bolt pattern, used primarily by the GM Ultium BEV3 vehicles. Compare across the rest of the Honda lineup at our Honda wheels and rims hub.

The GM Ultium BEV3 Platform and the Honda Prologue

The Prologue is the result of Honda's partnership with General Motors to deliver a Honda branded electric crossover ahead of Honda's own dedicated EV architecture. The vehicle is engineered on the GM Ultium BEV3 platform, which is the same architecture that underpins the Cadillac Lyriq and the Chevrolet Blazer EV. Honda designed the interior, the exterior styling, and the tuning, but the chassis, the battery pack format, the motor layout, and the wheel hardware spec come from the GM Ultium BEV3 platform.

Stock wheels on the Prologue are 19 inch on EX and Touring with a 21 inch wheel on Elite. Aftermarket diameter window on the Prologue runs 19 to 22 inch with widths from 8.5 to 10 inch front and rear, square fitment. Going below 19 inch is not in our measured fitment box because the Prologue's front brake assembly does not clear smaller diameters. The Prologue is heavier than a gasoline crossover of similar exterior size because of the battery pack, so wheel load rating matters more than it would on an equivalent gas vehicle. We confirm the load rating on every Prologue candidate wheel as part of the fitment check.

Every wheel we recommend is backed by our Fitment Guarantee. If a wheel does not fit, we pick up the wheels and refund 100 percent. No risk to you.

How We Confirm Fitment on Honda Prologue Wheels

Element Wheels measures fitment on the Prologue directly, across front wheel drive and all wheel drive configurations and across the EX, Touring, and Elite trims. That means hub bore confirmation at 74.5mm, clearance from the wheel to the fender at ride height and at full droop, gap behind the wheel to the suspension at full lock, brake caliper height across the Prologue's larger EV brake package, lug thread confirmation at M14x1.5, and a wheel load rating check against the Prologue's EV curb weight. The Prologue is heavier than a comparable gasoline crossover, so we treat load rating as a non optional step rather than an assumption. At our fitment facility in Chandler, Arizona, the Element Wheels team measures directly on the physical platforms we support. The Prologue shares its hub spec and brake assembly with the Cadillac Lyriq, so we cross check candidate wheels against the Lyriq measurements when a wheel is built for the wider GM Ultium BEV3 family. We don't pull these from manufacturer spec sheets the way most retailers do.

Honda Prologue Wheels and Rims FAQ

Get Honda Prologue Wheels Right the First Time

Pick the Prologue link above to see wheels and rims that fit. We measure on the Prologue directly, cross check against the Cadillac Lyriq on the same GM Ultium BEV3 architecture, and load rate every candidate wheel against EV curb weight. Find your fit and start enjoying your build sooner.