Mazda CX-30 Wheels and Rims

Mazda CX-30 Aftermarket Wheel Fitment

The Mazda CX-30 is Mazda's subcompact crossover, slotted between the smaller CX-3 and the larger CX-5 in the lineup, and launched as a 2020 model year on the Mazda3 SkyActiv platform. The CX-30 runs a 5x114.3 bolt pattern with a 67.1mm hub bore, an M12x1.5 thread pitch, and 5 lugs, the same hub spec as the Mazda3 hatch and sedan. Our measured aftermarket window is 16 to 20 inch diameter and 6.5 to 8.0 inch width square front and rear. The CX-30 has a relatively low 16 inch brake caliper height, which lets it run a smaller 16 inch winter wheel that some of the larger crossovers cannot accommodate. Pick your year range below for the fitment specs.

Find Your Mazda CX-30 Year Range

The CX-30 is a single-generation platform from 2020 forward, so there is one fitment box that covers every model year. Pick the year range to see wheels and rims that fit your specific CX-30.

The Mazda CX-30 Bolt Pattern

The Mazda CX-30 runs a 5x114.3 bolt pattern with a 67.1mm hub bore. The imperial nickname for this pattern is 5x4.5 because 114.3mm equals 4.5 inches exactly. The lug count is 5, the thread pitch is M12x1.5. This is the same hub spec used across the modern Mazda lineup including the Mazda3, the CX-5, and the CX-9, so wheels in this fitment family are widely available aftermarket.

One detail to flag because it catches some buyers. 5x114.3 is NOT the same as the 5x115 pattern used on some American sedans. The two sit roughly 0.7mm apart on the hub circle and a wheel built for one will not properly seat on the other. The 5x4.5 imperial nickname refers to 5x114.3 only. The 5x115 pattern lives on cars like the Chrysler 300 and the Dodge Charger and those wheels will not fit your CX-30. When you are shopping, confirm the wheel listing says 5x114.3 specifically. Compare across the rest of the Mazda lineup at our Mazda wheels and rims hub.

Diameter and Width Window for the CX-30

The CX-30 is the smallest crossover in the modern Mazda lineup that we cover on the SkyActiv 5-lug hub. Our measured aftermarket diameter window opens at 16 inch and tops at 20 inch. The width window runs from 6.5 to 8.0 inch square front and rear. The 16 inch floor is set by the brake caliper, which we measure at 16 inch on the CX-30. That is one inch lower than the CX-5 floor, which is what lets the CX-30 run a 16 inch winter wheel for tire chain compatibility or a cheap snow-tire setup, where the CX-5 has to stay at 17 inch.

The CX-30 is a square (non-staggered) crossover across all trims, including the CX-30 Turbo. Same wheel spec front and rear on every variant. Most aftermarket CX-30 buyers land at 18 or 19 inch for the upgraded look without losing too much sidewall on a small daily-driven crossover.

How We Confirm Fitment on Mazda CX-30 Wheels

Element Wheels measures fitment on the CX-30 directly. For the CX-30 that means clearance from the wheel to the fender, gap between the back of the wheel and the suspension, brake caliper height, hub bore confirmation at 67.1mm, lug stud height, and turning clearance with the wheel and tire installed. At our fitment facility in Chandler, Arizona, the Element Wheels team measures directly on the physical platforms we support. We don't pull specs from manufacturer sheets the way most retailers do.

That measurement work is what produced the diameter and width window on this page. It is also why every wheel we recommend is backed by our Fitment Guarantee. If a wheel does not fit, we pick up the wheels and refund 100 percent. No risk to you.

Mazda CX-30 Wheels and Rims FAQ

Get Mazda CX-30 Wheels Right the First Time

Click the year range above to see wheels and rims that fit. We measure the CX-30 directly across every model year from 2020 forward, confirm the 5x114.3 bolt pattern is not confused with 5x115, and tune the offset window against the CX-30 fender and brake. Find your fit and start enjoying your build sooner.