Rohana RFC3 Wheels & Rims

Rohana RFC3 Wheels at Element Wheels

The Rohana RFC3 is a multi spoke wheel from Rohana's Cross Forged RFC series, built around a deep concave face and a signature lip. We carry it in more than 100 size and finish combinations: three finishes, 19 and 20 inch diameters, and widths from 8.5 to 11 inches. We have detailed measurements for the vehicles these wheels go on, so the RFC3 setup we recommend is one that fits your car the first time. Every Rohana RFC3 wheel we sell is covered by our 100% Fitment Guarantee and free shipping on qualifying orders. Browse the finishes above, or use Shop by Vehicle to see only the RFC3 sizes that fit your car.

Rohana RFC3 Sizes and Concave Levels

Rohana rates the concave on RFC3 rims in four levels, and the level follows the width and offset. The 20x11 is the only size that reaches extreme deep concave, and it is the rear wheel in every staggered RFC3 build shown below.

Offsets run from +8mm to +73mm across the line. Bolt patterns include 5x112, 5x114.3, 5x115, 5x120, 5x120.7 (5x4.75), and 5x130, and each finish listing above has the full fitment table with the offset, center bore, and price for every size.

Rohana RFC3 Finishes

The RFC3 comes in three finishes: Silver Machined with a chrome lip, Gloss Black, and Bronze Machined. Rohana makes the silver version's lip from stainless steel, so it is the finish that shows the lip the design is built around. Bronze Machined is the newest of the three, which Rohana introduced on a 2025 Audi A5.

Every listing includes the AI Visualizer, so you can see the exact finish on your own car before you buy.

Rohana Cross Forged Construction

Rohana groups the RFX, RFC, and RFV series as its Cross Forged line. Each wheel is spun at high speed while pressure is applied to the barrel, which compresses and aligns the metal grain. Rohana says the process makes the wheel lighter and stronger, and closer to a fully forged standard.

Every RFC3 in our catalog carries a load rating of 1,676 lbs per wheel.

Rohana RFC3 Fitments

Our customer gallery has an RFC3 build on a 2014-2019 Chevrolet Corvette C7 Stingray: Bronze Machined in a staggered setup with a 19x9.5 +53mm front and a 20x11 +73mm rear. See the Corvette build.

Rohana's own launch builds show the same pattern on other cars. A Nissan Z runs a 20x9 front with a 20x11 rear, a sixth generation Camaro ZL1 uses a 20x9 front to clear its big front brakes with a deep concave 20x11 rear, and an Audi A5 runs a square set of 20x9s.

Other Rohana Cross Forged Designs

If you like the RFC3's construction but want a different face, the RFC10 is the other design in the RFC series, and the RFX series carries the same Cross Forged process in more diameters. The full lineup is on our Rohana wheels page.

How We Confirm Fitment on Rohana RFC3 Wheels

We measure fitment on real vehicles at our Chandler, Arizona facility rather than trusting spec sheets: wheel to fender clearance, strut clearance, caliper height, hub bore, lug seat geometry, and turning clearance at full lock. On the RFC3 the offset range is unusually wide, from +8mm to +73mm, so the same 20x11 can sit flush on one car and tucked deep inside the fender on another. We match the offset to your platform before anything ships.

That measurement work is why every Rohana RFC3 set we recommend for your vehicle is backed by our Fitment Guarantee. If a wheel does not fit, we pick up the wheels and refund 100 percent.

Rohana RFC3 Wheels and Rims FAQ

Get Rohana RFC3 Wheels Right the First Time

Pick a finish above or use Shop by Vehicle and let us narrow the RFC3 to your exact car. Three finishes, five sizes, and four concave levels to choose from. Get the fitment settled today and enjoy the build that much sooner.

Related Wheels

Shop by Wheel Size

Shop by Finish

Shop by Style

Shop by Vehicle & Use